Stable and Highly Flexible Perovskite Solar Cells with Power Conversion Efficiency Approaching 20% by Elastic Grain Boundary Encapsulation

Open AccessCCS ChemistryRESEARCH ARTICLE1 Jul 2021Stable and Highly Flexible Perovskite Solar Cells with Power Conversion Efficiency Approaching 20% by Elastic Grain Boundary Encapsulation Chengda Ge†, Ziqi Yang†, Xiaoting Liu, Yilong Song, Anran Wang and Qingfeng Dong Chengda Ge† State Key Laboratory of Supramolecular Structure and Materials, College of Chemistry, Jilin University, Changchun 130012 , Ziqi Yang† State Key Laboratory of Supramolecular Structure and Materials, College of Chemistry, Jilin University, Changchun 130012 , Xiaoting Liu State Key Laboratory of Supramolecular Structure and Materials, College of Chemistry, Jilin University, Changchun 130012 , Yilong Song State Key Laboratory of Supramolecular Structure and Materials, College of Chemistry, Jilin University, Changchun 130012 , Anran Wang State Key Laboratory of Supramolecular Structure and Materials, College of Chemistry, Jilin University, Changchun 130012 and Qingfeng Dong *Corresponding author: E-mail Address: [email protected] State Key Laboratory of Supramolecular Structure and Materials, College of Chemistry, Jilin University, Changchun 130012 https://doi.org/10.31635/ccschem.020.202000335 SectionsSupplemental MaterialAboutAbstractPDF ToolsAdd to favoritesTrack Citations ShareFacebookTwitterLinked InEmail Here, we show that flexible perovskite solar cells (PSCs) with high operational stability and power conversion efficiency (PCE) approaching 20% were achieved by elastic grain boundary (GB) encapsulation. An introduction of trimethyltrivinyl-cyclotrisiloxane (V3D3) and solvent annealing (SA) resulted in an in situ cross-linking reaction between GBs and enlarged grain size that enabled oriented charge-transport properties to be achieved synchronously, leading to reduced sheet resistance with a high fill factor (FF) up to 82.93% in flexible PSCs. Meanwhile, the insulating elastic V3D3 for GB encapsulation suppressed the carrier recombination substantially, as well as ion migration, which enhanced both the mechanical and the operational stability dramatically in flexible PSCs. Additionally, more than 73% of its initial PCE was retained even after 10,000 bending cycles, with 83% of its stabilized PCE remaining after 300 h of continuous operation at maximum power point (MPP) condition under one sun illumination without cooling. Download figure Download PowerPoint Introduction Flexible solar cells (FSCs), which could be fabricated by the scalable roll-to-roll technology, are receiving sustained attention for their merits, including lightweight, flexibility, portability, and compatibility with curved surfaces.1–3 Inorganic-semiconductor-based FSCs, such as c-Si,4,5 CIGS,6–8 and AsGa,9–11 have achieved good efficiency,12 but the low flexibility and high-cost limit their practical application. On the other hand, organic solar cells, as types of attractive FSC candidates, show excellent flexibility.13 However, their efficiencies are still much lower than those of commercialized FSCs.14,15 Recently, FSCs based on metal halide hybrid perovskite materials attracted much attention due to their solution processability,16–18 low cost,17–19 and rapidly improved device efficiency.20 Several investigators have reported efficient single-junction flexible perovskite solar cells (PSCs) by using commercial polymer/indium tin oxide (ITO) substrate with a power conversion efficiency (PCE) of >19%.21,22 However, the inorganic nature of the high modulus microscopic structures for both perovskite grains and the ITO electrode itself constrains the flexibility of PSCs. Furthermore, most of efficient, flexible PSCs based on commercialized ITO substrate undoubtedly degrade after only hundreds of bending cycles due to the ceramic nature of ITO and degradation of fragile perovskite film during bending.23–28 In fact, it is more challenging for PSCs to possess high flexibility besides high device efficiency, since high-quality pin-hole-free perovskite films are relatively difficult to fabricate on hydrophobic flexible substrates under low film-forming temperature, compared with their rigid-substrate counterparts.29 More importantly, the operational stability of flexible PSCs still lags behind, compared with the rigid ones, which restrains the development of flexible PSCs substantially. Therefore, investigations concerning the operation stability of flexible PSCs are urgently required. The suppression of ion migration is believed to be an essential parameter to consider regarding stability improvement of flexible PSCs30 due to their fragile grain boundaries (GBs) with much lower crystallinity, compared with the rigid PSCs; it is presumed that the hysteresis behavior at the GBs facilitates ion migration pathways in flexible devices.31 In this work, highly flexible PSCs with good operational stability were realized by introducing in situ cross-linked elastic GB encapsulation, formed by thermal excitation with a unique cross-linker that favored enrichment of the cross-linking network, followed by a solvent annealing (SA)-induced phase separation between the inorganic grains and the organic cross-linkers. Also, the SA process-induced high-quality perovskite films with both enhanced crystallinity and charge-transport properties, which led to high efficiency and good mechanical properties of the PSCs. Meanwhile, the insulating GB encapsulation resulted in a suppressed ion migration rate and reduced carrier recombination across GBs, which enhanced the device performance considerably. Therefore, flexible PSCs displayed PCE approaching 20% with dramatically improved mechanical property >73% of the initial PCE value, which was retained even after 10,000 bending cycles. Moreover, significant enhancement of operational stability was achieved under continuous output at a maximum power point (MPP) condition under one sun illumination without cooling. Experimental Methods Device fabrication All solvents used in the experiments were purchased from Sigma-Aldrich (Shanghai, China). Trimethyltrivinyl-cyclotrisiloxane (V3D3) was bought from TCI (Shanghai, China). The patterned ITO/glass substrates were cleaned by sonication in isopropyl alcohol and acetone. A 2 mg/mL of poly[bis(4-phenyl)(2,4,6-trimethylphenyl)]amine (PTAA) solution was spin-coated on flexible substrates at 6000 rpm for 60 s, followed by a thermal annealing treatment at 100 °C for 10 min. The perovskite layer used in our flexible PSC is Cs0.05(FA0.87MA0.13)0.95Pb(I0.87Br0.13)3. CsI was dissolved in dimethyl sulfoxide (DMSO) in advance; methylamine hydrobromide (MABr), lead bromide (PbBr2), formamidinium iodide (FAI), and lead iodide (PbI2) were dissolved in a mixed solvent of dimethylformamide (DMF) and DMSO (v/v 4∶1), to form the perovskite precursor solution (1.4 mmol/mL).32 The conjugated electron-interface layer material, PFN-Br,33,34 was spin-coated on the PTAA layer at 4000 rpm for 30 s, and perovskite films were obtained by a sequential spin coating of 120 μL perovskite solution and added antisolvent, chlorobenzene, to induce rapid crystallization of the perovskite precursor solution.35 Then SA was performed by adding 2 μL DMSO as solvent vapor at 100 °C for 20 min, followed by thermal annealing treatment for 40 min to create the reference or the prototype device (control). For the fabrication of the new cross-linked device, the V3D3 monomer was added directly into the perovskite precursor solution at a concentration of 2‰ or was added into the antisolvent at a concentration of 0.3 mg/mL to cross-link the polymer films. After antisolvent treatment, the film was placed in an N2-filled glovebox at room temperature for 25 min and then preheated at 80 °C for 1 min, followed by annealing in the same way as the reference device. After that, 20 nm C60, 8 nm BCP (2,9-dimethyl-4,7-diphenyl-1,10-PhenanthrolineSynonym), and 80 nm Cu were deposited on the perovskite film with an ITO/Cu overlap area of 10 mm2 via step by step thermal vacuum evaporation to generate the highly flexible PSCs. Characterizations Current–voltage (J–V) characteristics of flexible PSCs were recorded in N2-filled glovebox (Mikrouna Co., Ltd., Shanghai, China) by using Keithley 2400 under an AAA solar simulator (Crowntech. Inc., Pennsylvania, USA; 100 mW/cm2, AM 1.5G irradiation). The scan range was from −0.1 to 1.2 V, and the delay time was 33 ms. A 4 mm2 photomask was used during measurement. The standard silicon cell was corrected for National Renewable Energy Laboratory as reference cell calibration. The external quantum efficiency (EQE) measurement was performed on the QTest Hifinity5 system (Crowntech. Inc.), and monochromatic light was calibrated by the reference silicon cell before EQE measurement. The scanning Kelvin probe force microscopy (KPFM) was used together with atomic force microscopy (AFM; Bruker Dimension FastScann, Massachusetts, USA) to carry out electrical potential distribution measurement of the amplitude modulation (AM-KPFM) mode. X-ray diffraction (XRD) indexing and data collection were performed on an Ultima VI diffractometer with Cu Kα (λ = 0.15418 nm) at 293 K. Results and Discussion Preparation of elastic GBs and morphology characterization Branched olefin-functionalized monomers could be introduced into a growing polymer intentionally for an in situ cross-link polymerization, initiated by heating without the production of harmful byproducts such as H2O. Meanwhile, the multifunctional monomers would generate highly branched dendrimer networks over a long-range (Figure 1a). Based on this principle, a multifunctional alkene semiorganic monomer, V3D3, was used as the cross-linker, as illustrated in Figure 1b, to form three-dimensional (3D) cross-linked networks directly by low-temperature thermal-initiated polymerization. It is worth noting that the organosilicon, V3D3, was different from SiO2-based doping materials such as tetraethoxysilane (TEOS) used in rigid PSCs to improve the electrochemical performance reported previously36 ( Supporting Information Figure S3), which preferred to form a rigid core–shell structure with perovskite grain instead of flexible elastic-GBs. Figure 1 | (a) Illustration of the SA treatment. (b) The polymerization reaction of V3D3. (c–g) Top view of SEM images of different perovskite films with various methods. SA, solvent annealing; V3D3, trimethyltrivinyl-cyclotrisiloxane; SEM, scanning electron microscopy. Download figure Download PowerPoint It is difficult to establish an in situ cross-linking reaction when the ratio of the doping monomers is relatively low in the perovskite precursor. Here, we employed SA treatment to increase the monomers in GBs effectively, which enabled the cross-linking reaction to form elastic GB encapsulation, as illustrated in Figure 1a. The enrichment of the insulating polymers was evidenced by scanning electron microscopy (SEM) analysis, as shown in the images in Figures 1c–1g. The cross-linking organic composition is distributed homogeneously over the whole perovskite film without SA (Figure 1e). However, the cross-linking organic composition was enriched in GBs efficiently, forming domain structures with the adoption of the SA method. The SEM images demonstrated that the SA treatment facilitated a potent phase separation of the inorganic grains and the organic cross-linkers to enable in situ formation of elastic GBs. Multiple characterization methods, including KPFM, energy-dispersive X-ray (EDX) spectra, and transmission electron microscopy (TEM), were carried out to characterize the structures using different scales. From KPFM images (Figures 2a–2f), the surface potential was similar on the surface of both grain and GBs for the control (prototype) perovskite films. In contrast, we noted a sharply varied surface potential indicative of the differences in composition between the grains and GBs. This observation was ascribed to the enriched cross-linker composition in GBs, just as expected, which was also consistent with the findings of the SEM images. KPFM measurement was used to study the differences of surface potential between grain and GBs in this work, with the measured values being relative, rather than absolute. EDX was used to investigate the distribution of insulating polymers in the perovskite films. The doping ratio was increased to 2 mol %, in order to make the element content reach the EDX detection limit. The characteristic elements of silicon (Si) and oxygen (O) were identified in the white region at the grain or domain boundary, while the dark region showed almost no signal response from the characteristic Si and O elements (Figures 2g–2i), consistent with the observations in Figure 1. Meanwhile, the bright region outside the perovskite grains in the TEM images (Figures 2j) indicated further that the polymer was covered around the perovskite grains, suggesting the formation of elastic GBs. Figure 2 | Characterization of elastic GB encapsulation. (a and b) Height and (d and e) KPFM mode AFM images for perovskite films with or without elastic GBs and the distribution of (c) height and (f) the surface potential. (g) SEM, (h and i) EDX images, and (j) TEM images of perovskite films with elastic GBs. GB, grain boundary; KPFM, Kelvin probe force microscopy; AFM, atomic force microscopy; SEM, scanning electron microscopy; EDX, energy-dispersive X-ray. Download figure Download PowerPoint Evaluation of defect and electrical properties The SA treatment of the cross-linked perovskite films induced continuous cross-linked elastic insulating networks across the GBs, and also realized secondary grain growth successfully with a significant increase in grain size. The insulating GB encapsulation promoted vertical charge transport and suppressed carrier recombination across GBs. Meanwhile, it contributed significantly to the reduction of trap-state density and improvement of electron mobility with structure retention, evidenced by XRD patterns (Figure 3a), which was a key factor considered for improving the charge-transport properties in the sandwiched architecture of the PSC device. The space-charge-limited current (SCLC) method was used to evaluate the effect of the cross-linking process. According to described previous methods, the trap-state density was estimated by the formula37–39: V TFL = e n t L 2 2 ɛ ɛ 0 (1)where nt is the trap-state density, and VTFL is the trap-filled limited voltage. The VTFL could be acquired from the dark J–V curve of the electron-only device with a device structure, ITO/C60/Perovskite/C60/BCP/Cu (Figure 3c). After V3D3 treatment, nt was reduced significantly to 6.74 × 1015 cm−3, compared with 1.24 × 1016 cm−3 in regular perovskite film. This result was consistent with the time-resolved photoluminescence (TRPL) measurement (Figure 3b), in which a longer fluorescence lifetime was apparent of the cross-linked perovskite film, compared with the control sample, which also indicated a marked reduction in defect concentration.40 Furthermore, there were two orders of magnitude increment in electron mobility of the V3D3 cross-linked devices, estimated as 1.03 × 10−3 cm2 V−1 s−1, compared with the reference device, 1.02 × 10−5 cm2 V−1 s−1, which were calculated using the Mott–Gurney law, as follows:38,41 J D = 9 ɛ ɛ 0 μ V b 2 8 L 3 (2) Figure 3 | Characterization of perovskite films with V3D3 cross-linking. (a) XRD measurement of control and cross-linked perovskite films. (b) TRPL measurement of control and cross-linked films. (c) Dark-state J–V measurement of an electron-only device. (d) Vertical direction ion migration measurement. (e and f) Comparison of transverse and longitudinal conductivity. V3D3, trimethyltrivinyl-cyclotrisiloxane; XRD, X-ray diffraction; TRPL, time-resolved photoluminescence; J–V, current–voltage characteristic. Download figure Download PowerPoint It is noteworthy that the insulating GB encapsulation suppressed the ion migration substantially in a vertical direction across the polycrystalline perovskite film, which benefited efficient defect passivation, as well as blockage of the ion migration pathways. Figure 3d shows the current tracking under 0.1 sun illumination with and without cross-linking under the vertical electric field, used to evaluate the current contributed by the ion migration effect. The current variation in the initial stage was reduced significantly in the cross-linking films (Figure 3d), which paralleled a diminution of the ion migration effect in a vertical direction across the perovskite film. Meanwhile, the insulation of the elastic GB encapsulation reduced the charge concentration at GBs profoundly, which suppressed the charge recombination across GBs, resulting in an improved vertical charge-transport property (Figures 3e and 3f), as well as blocking the lateral charge-transport pathways. These insulation properties are always preferred in photovoltaic device systems, as they contribute to an optimized fill factor (FF) of these devices, which, favorably, was the main achievement of our fabricated GB encapsulation device. Characterization of photovoltaic performance The insulating elastic GB encapsulation, which suppressed carrier recombination, as well as the ion migration effect, led to a dramatic enhancement of the photovoltaic performance of our flexible PSCs, compared with the prototypes without elastic GBs (Figure 4b). The inverted planar device structure of ITO/PTAA/PFN-Br/PVKcross-linker/C60/BCP/Cu (4a) was used to evaluate the performance of the flexible PSCs. After introducing V3D3 cross-linking into the fabrication process, the flexible PSC showed a JSC of 22.33 mA/cm2, a VOC of 1.08 V, an FF of 82.93%, and a champion PCE of 20%, which was a demonstration of a significant increase in PCE, compared with the reference device with a JSC of 21.49 mA/cm2, a VOC of 1.06 V, an FF of 81.83%, and a lower PCE of 18.64%. Here, the reference device was already well optimized as the control device and had approached the best value of flexible PSCs reported earlier. Notably, the highest FF of 82.93% was realized in our flexible PSCs, which was the highest value ever reported in flexible PSCs, and similar to the best value obtained in rigid devices. The excellent FF was believed to be a benefit from our insulating GB encapsulation-induced low-trap density and an outstanding charge carrier transport properties. Figure 4 | Photovoltaic performance of flexible perovskite solar cells. (a) Structure of flexible perovskite solar cells. (b) J–V measurement of control and cross-linked device. (c) Image of flexible PSCs sample. (d) EQE measurement of our flexible PSCs. J–V, current–voltage characteristic; EQE, external quantum efficiency. Download figure Download PowerPoint Mechanical property and stability test The elastic cross-linking strategy adapted in the PSCs fabrication enabled the flexible "grain-elater-grain" encapsulation to release mechanical stress generated during bending, as well as thermal expansion of flexible PSCs, which contributed significantly to excellent device stabilities under both continuous bending and operational conditions. As shown in Figure 5d, regular flexible PSCs showed an apparent decay within 700-times of bending cycles, similar to most results reported previously. On the contrary, devices with V3D3 showed dramatically enhanced bending stability under the same test condition with a small bending radius, and restoration of >70% of the initial PCE, even after 10,000 bending cycles with a bending radius of 2.5 mm, which, to our knowledge, was one of the best values in flexible PSCs on ITO substrate (Table 1), indicating that the elastic GB structure was recoverable and eliminated the damage of the fragile GBs during bending effectively. In order to investigate further the degradation mechanism, the transformation of grain structures was tracked in stretched perovskite films by SEM measurements. The reference perovskite film stretched ruinously by the universal material testing machine during the evaluation of the damage pathways. The film broke randomly and even destroyed the grain itself (Figure 5a). In contrast, the elastic-V3D3 cross-linked perovskite films showed distinct separation of grains or domain boundaries, but retained grain structure under stretching (Figure 5b), leading us to infer that the degradation mechanism was attributed to the high rigidity of the GBs in regular perovskite films, while the elastic ones preferred to release the applied stress and deformation with a recoverable characteristic. Figure 5 | Mechanical and operational stability of FSCs. (a) Brittle rupture of flexible PSCs after a tensile experiment. (b) Regular fracture after a tensile experiment. (c) Continuous output at MPP of flexible PSCs. (d) Bending test of the control device and cross-linked device in which the bending radius is 2.5 mm. FSCs, Flexible solar cells; PSCs, perovskite solar cells; MPP, maximum power point. Download figure Download PowerPoint Table 1 | Summary of Some Classic Research About Flexible PSCs Year Substrate PCE (%) Times of Bending/Retention of PCE (%) Bending Radius (mm) Stability Test Condition Retention of PCE (%) References 2013 PET/ITO 6.4 Not given Not given NA for FSC — 42 2016 PET/ITO 16.09 300/>91 5 NA for FSC — 39 2017 PEN/ITO 15.4 300/>60 4, 8, 12 NA for FSC — 43 2017 PET/ITO 18.4 1000/88.6 4.4 Storage/100 days 88.8 44 2018 PET/ITO 18.4 5000/83 4 Storage/60 days ∼80 45 2019 PET/ITO 18.1 Not given Not given Storage/960 h 72 46 2019 PET/ITO 15.12 5000/85 2.5 NA for FSC — 47 2019 Mica/ITO 18 5000/91.7 5 Storage/85 °C, 85% RH >60 48 2019 PEN/ITO 19.11 2000/93 10 Storage/85 °C, 1000 h 68 22 2019 PEN/ITO 19.51 6000/95 8 Storage/1000 h 90 21 2019 PEN/ITO 20 10,000/73.5 2.5 Operation/300 h/MPP 83 This work Abbreviations: NA, not applicable; PET, polyethylene terephthalate; PEN, polyethylene naphthalate; RH, relative humidity. The flexible PSCs also showed high continuous operational stability at MPP conditions under one sun illumination without a cooling stage when the device achieved a measured, balanced temperature of ∼64 °C. On the contrary, the PSCs without the cross-linking degraded rapidly in the first 10 h (∼10 h). The cross-linked flexible PSCs with the elastic GBs retained ∼83% of its initial efficiency, following 300 h of continuous operation after a balanced thermal point, as shown in Figure 5c. It was believed that the enhanced stability was benefited from the high-quality perovskite films with elastic GB encapsulation, as well as the suppressed ion migration rate. Besides, ITO with a flexible polymer substrate always has poor heat stability, unlike rigid substrates, due to the significant differences in the coefficients of thermal expansion between layers. Moreover, the increased absorption of UV light in polymer substrates other than glass would cause a further increase in substrate temperature49; thus, stress damage is inevitable. Here, the grain–elater–grain hybrid structures in the lateral direction overcame this issue effectively by retaining the grain structure during expansion and enhanced the operational stability, compared with the prototype grain–grain structures. Conclusions The SA-induced in situ cross-linked elastic GB encapsulation, formed by V3D3, enabled high-quality perovskite films in terms of optimized grain structure and improved charge-transport properties. Meanwhile, this approach suppressed the ion migration rate and reduced carrier recombination, which enhanced the device performance dramatically, including device efficiency, bending stability, as well as operational stability. All these improvements indicated that the cross-linked insulating elastic GB encapsulation strategy provides a prospective pathway to develop high-performance flexible PSCs. Supporting Information Supporting Information is available. Conflicts of Interest The authors declare no conflict of interest. Data availability The data that support the plots within this work are available from the corresponding author upon request. Acknowledgments Q.D. conceived the idea, supervised the project, and conducted the initial experiment. C.G. and Z.Y. fabricated the devices, performed the characterization, and did most of the experiments. X.L., Y.S., and A.W. contributed to the device characterization. Q.D. and C.G. wrote the paper. This work was supported by the National Natural Science Foundation of China (no. 21875089). References 1. Yang D.; Yang R.; Priya S.; Liu S. F.Recent Advances in Flexible Perovskite Solar Cells: Fabrication and Applications.Angew. Chem. Int. Ed.2019, 58, 4466–4483. Google Scholar 2. Di Giacomo F.; Zardetto V.; D'Epifanio A.; Pescetelli S.; Matteocci F.; Razza S.; Di Carlo A.; Licoccia S.; Kessels W. M. M.; Creatore M.; Brown T. M.Flexible Perovskite Photovoltaic Modules and Solar Cells Based on Atomic Layer Deposited Compact Layers and UV-Irradiated TiO2 Scaffolds on Plastic Substrates.Adv. Energy Mater.2015, 5, 1401808. Google Scholar 3. Hu X.; Meng X.; Zhang L.; Zhang Y.; Cai Z.; Huang Z.; Su M.; Wang Y.; Li M.; Li F.; Yao X.; Wang F.; Ma W.; Chen Y.; Song Y.A Mechanically Robust Conducting Polymer Network Electrode for Efficient Flexible Perovskite Solar Cells.Joule2019, 3, 2205–2218. Google Scholar 4. Bahabry R. R.; Kutbee A. T.; Khan S. M.; Sepulveda A. C.; Wicaksono I.; Nour M.; Wehbe N.; Almislem A. S.; Ghoneim M. T.; Torres Sevilla G. A.; Syed A.; Shaikh S. F.; Hussain M. M.Corrugation Architecture Enabled Ultraflexible Wafer-Scale High-Efficiency Monocrystalline Silicon Solar Cell.Adv. Energy Mater.2018, 8, 1702221. Google Scholar 5. Hwang I.; Um H.-D.; Kim B.-S.; Wober M.; Seo K.Flexible Crystalline Silicon Radial Junction Photovoltaics with Vertically Aligned Tapered Microwires.Energy Environ. Sci.2018, 11, 641–647. Google Scholar 6. Wang Y.-C.; Wu T.-T.; Chueh Y.-L.A Critical Review on Flexible Cu(In, Ga)Se2 (CIGS) Solar Cells.Mater. Chem. Phys.2019, 234, 329–344. Google Scholar 7. Colombara D.; Werner F.; Schwarz T.; Canero Infante I.; Fleming Y.; Valle N.; Spindler C.; Vacchieri E.; Rey G.; Guennou M.; Bouttemy M.; Manjon A. G.; Peral Alonso I.; Melchiorre M.; El Adib B.; Gault B.; Raabe D.; Dale P. J.; Siebentritt S.Sodium Enhances Indium-Gallium Interdiffusion in Copper Indium Gallium Diselenide Photovoltaic Absorbers.Nat. Commun.2018, 9, 826. Google Scholar 8. Yang K. J.; Kim S.; Kim S. Y.; Ahn K.; Son D. H.; Kim S. H.; Lee S. J.; Kim Y. I.; Park S. N.; Sung S. J.; Kim D. H.; Enkhbat T.; Kim J.; Jeon C. W.; Kang J. K.Flexible Cu2ZnSn(S, Se)4 Solar Cells with Over 10% Efficiency and Methods of Enlarging the Cell Area.Nat. Commun.2019, 10, 2959. Google Scholar 9. Moon S.; Kim K.; Kim Y.; Heo J.; Lee J.Highly Efficient Single-Junction GaAs Thin-Film Solar Cell on Flexible Substrate.Sci. Rep.2016, 6, 30107. Google Scholar 10. Metaferia W.; Schulte K. L.; Simon J.; Johnston S.; Ptak A. J.Gallium Arsenide Solar Cells Grown at Rates Exceeding 300 Micron h(-1) by Hydride Vapor Phase Epitaxy.Nat. Commun.2019, 10, 3361. Google Scholar 11. Park S.; Simon J.; Schulte K. L.; Ptak A. J.; Wi J.-S.; Young D. L.; Oh J.Germanium-on-Nothing for Epitaxial Liftoff of GaAs Solar Cells.Joule2019, 3, 1782–1793. Google Scholar 12. Ono L. K.; Qi Y.; Liu S.Progress Toward Stable Lead Halide Perovskite Solar Cells.Joule2018, 2, 1961–1990. Google Scholar 13. Li Y.; Xu G.; Cui C.; Li Y.Flexible and Semitransparent Organic Solar Cells.Adv. Energy Mater.2018, 8, 1701791. Google Scholar 14. Pagliaro M.; Ciriminna R.; Palmisano G.Flexible Solar Cells.ChemSusChem2008, 1, 880–891. Google Scholar 15. Zhang Y. X.; Fang J.; Li W.; Shen Y.; Chen J. D.; Li Y.; Gu H.; Pelivani S.; Zhang M.; Li Y.; Tang J. X.Synergetic Transparent Electrode Architecture for Efficient Non-Fullerene Flexible Organic Solar Cells with >12% Efficiency.ACS Nano2019, 13, 4686–4694. Google Scholar 16. Ball J. M.; Lee M. M.; Hey A.; Snaith H. J.Low-Temperature Processed Meso-Superstructured to Thin-Film Perovskite Solar Cells.Energy Environ. Sci.2013, 6, 1739–1743. Google Scholar 17. Wang Q.; Shao Y.; Dong Q.; Xiao Z.; Yuan Y.; Huang J.Large Fill-Factor Bilayer Iodine Perovskite Solar Cells Fabricated by a Low-Temperature Solution-Process.Energy Environ. Sci.2014, 7, 2359–2365. Google Scholar 18. He M.; Li B.; Cui X.; Jiang B.; He Y.; Chen Y.; O'Neil D.; Szymanski P.; Ei-Sayed M. A.; Huang J.; Lin Z.Meniscus-Assisted Solution Printing of Large-Grained Perovskite Films for High-Efficiency Solar Cells.Nat. Commun.2017, 8, 16045. Google Scholar 19. Chen H.; Wei Z.; Zheng X.; Yang S.A Scalable Electrodeposition Route to the Low-Cost, Versatile and Controllable Fabrication of Perovskite Solar Cells.Nano Energy2015, 15, 216–226. Google Scholar 20. Jiang Q.; Zhao Y.; Zhang X.; Yang X.; Chen Y.; Chu Z.; Ye Q.; Li X.; Yin Z.; You J.Surface Passivation of Perovskite Film for Efficient Solar Cells.Nat. Photo.2019, 13, 460–466. Google Scholar 21. Huang K.; Peng Y.; Gao Y.; Shi J.; Li H.; Mo X.; Huang H.; Gao Y.; Ding L.; Yang J.High-Performance Flexible Perovskite Solar Cells via Precise Control of Electron Transport Layer.Adv. Energy Mater.2019, 2019, 1901419. Google Scholar 22. Cao B.; Yang L.; Jiang S.; Lin H.; Wang N.; Li X.Flexible Quintuple Cation Perovskite Solar Cells with High Efficiency.J. Mater. Chem. A2019, 7, 4960–4970. Google Scholar 23. Wang C.; Guan L.; Zhao D.; Yu Y.; Grice C. R.; Song Z.; Awni R. A.; Chen J.; Wang J.; Zhao X.; Yan Y.Water Vapor Treatment of Low-Temperature Deposited SnO2 Electron Selective Layers for Efficient Flexible Perovskite Solar Cells.ACS Energy Lett.2017, 2, 2118–2124. Google Scholar 24. Zhao D.; Zhang C.; Kim H.; Guo L. J.High-Performance Ta2O5/Al-Doped Ag Electrode for Resonant Light Harvesting in Efficient Organic Solar Cells.Adv. Energy Mater.2015, 5, 1500768. Google Scholar 25. Zhang C.; Zhao D.; Gu D.; Kim H.; Ling T.; Wu Y. K.; Guo L. J.An Ultrathin, Smooth, and Low-Loss Al-Doped Ag Film and Its Application as a Transparent Electrode in Organic Photovoltaics.Adv. Mater.2014, 26, 5696–5701. Google Scholar 26. Yoon J.; Sung H.; Lee G.; Cho W.; Ahn N.; Jung H. S.; Choi M.Superflexible, High-Efficiency Perovskite Solar Cells Utilizing Graphene Electrodes: Towards Future Foldable Power Sources.Energy Environ. Sci.2017, 10, 337–345. Google Scholar 27. Heo J. H.; Lee M. H.; Han H. J.; Patil B. R.; Yu J. S.; Im S. H.Highly Efficient Low Temperature Solution Processable Planar Type CH3NH3PbI3 Perovskite Flexible Solar Cells.J. Mater. Chem. A2016, 4, 1572–1578. Google Scholar 28. Wang C.; Zhao D.; Yu Y.; Shrestha N.; Grice C. R.; Liao W.; Cimaroli A. J.; Chen J.; Ellingson R. J.; Zhao X.; Yan Y.Compositional and Morphological Engineering of Mixed Cation Perovskite Films for Highly Efficient Planar and Flexible Solar Cells with Reduced Hysteresis.Nano Energy2017, 35, 223–232. Google Scholar 29. Hou L.; Wang Y.; Liu X.; Wang J.; Wang L.; Li X.; Fu G.; Yang S.18.0% Efficiency Flexible Perovskite Solar Cells Based on Double Hole Transport Layers and CH3NH3PbI3-xClx with Dual Additives.J. Mater. Chem. C2018, 6, 8770–8777. Google Scholar 30. Xing J.; Wang Q.; Dong Q.; Yuan Y.; Fang Y.; Huang J.Ultrafast Ion Migration in Hybrid Perovskite Polycrystalline Thin Films Under Light and Suppression in Single Crystals.Phys. Chem. Chem. Phys.2016, 18, 30484–30490. Google Scholar 31. Li X.; Zhang W.; Wang Y. C.; Zhang W.; Wang H. Q.; Fang J.In-Situ Cross-Linking Strategy for Efficient and Operationally Stable Methylammoniun Lead Iodide Solar Cells.Nat. Commun.2018, 9, 3806. Google Scholar 32. Saliba M.; Matsui T.; Seo J. Y.; Domanski K.; Correa-Baena J. P.; Nazeeruddin M. K.; Zakeeruddin S. M.; Tress W.; Abate A.; Hagfeldt A.; Gratzel M.Cesium-Containing Triple Cation Perovskite Solar Cells: Improved Stability, Reproducibility and High Efficiency.Energy Environ. Sci.2016, 9, 1989–1997. Google Scholar 33. Hong S.; Lee J.; Kang H.; Kim G.; Kee S.; Lee J.-H.; Jung S.; Park B.; Kim S.; Back H.; Yu K.; Lee K.High-Efficiency Large-Area Perovskite Photovoltaic Modules Achieved via Electrochemically Assembled Metal-Filamentary Nanoelectrodes.Sci. Adv.2018, 4, 3604. Google Scholar 34. Lee J.; Kang H.; Kim G.; Back H.; Kim J.; Hong S.; Park B.; Lee E.; Lee K.Achieving Large-Area Planar Perovskite Solar Cells by Introducing an Interfacial Compatibilizer.Adv. Mater.2017, 29, 1606363. Google Scholar 35. Xiao M.; Huang F.; Huang W.; Dkhissi Y.; Zhu Y.; Etheridge J.; Gray-Weale A.; Bach U.; Cheng Y. B.; Spiccia L.A Fast Deposition-Crystallization Procedure for Highly Efficient Lead Iodide Perovskite Thin-Film Solar Cells.Angew. Chem. Int. Ed.2014, 53, 9898–9903. Google Scholar 36. Bai Y.; Lin Y.; Ren L.; Shi X.; Strounina E.; Deng Y.; Wang Q.; Fang Y.; Zheng X.; Lin Y.; Chen Z.-G.; Du Y.; Wang L.; Huang J.Oligomeric Silica-Wrapped Perovskites Enable Synchronous Defect Passivation and Grain Stabilization for Efficient and Stable Perovskite Photovoltaics.ACS Energy Lett.2019, 4, 1231–1240. Google Scholar 37. Bube R. H.Trap Density Determination by Space-Charge-Limited Currents.J. Appl. Phys.1962, 33, 1733–1737. Google Scholar 38. Dong Q.; Fang Y.; Shao Y.; Mulligan P.; Qiu J.; Cao L.; Huang J.Electron-Hole Diffusion Lengths >175 μm in Solution-Grown CH3NH3PbI3 Single Crystals.Science2015, 347, 967–970. Google Scholar 39. Yang D.; Yang R.; Ren X.; Zhu X.; Yang Z.; Li C.; Liu S. F.Hysteresis-Suppressed High-Efficiency Flexible Perovskite Solar Cells Using Solid-State Ionic-Liquids for Effective Electron Transport.Adv. Mater.2016, 28, 5206–5213. Google Scholar 40. Duan X.; Li X.; Tan L.; Huang Z.; Yang J.; Liu G.; Lin Z.; Chen Y.Controlling Crystal Growth via an Autonomously Longitudinal Scaffold for Planar Perovskite Solar Cells.Adv. Mater.2020, 32, 2000617. Google Scholar 41. Lin Y.; Fang Y.; Zhao J.; Shao Y.; Stuard S. J.; Nahid M. M.; Ade H.; Wang Q.; Shield J. E.; Zhou N.; Moran A. M.; Huang J.Unveiling the Operation Mechanism of Layered Perovskite Solar Cells.Nat. Commun.2019, 10, 1008. Google Scholar 42. Docampo P.; Ball J. M.; Darwich M.; Eperon G. E.; Snaith H. J.Efficient Organometal Trihalide Perovskite Planar-Heterojunction Solar Cells on Flexible Polymer Substrates.Nat. Commun.2013, 4, 2761. Google Scholar 43. Heo J. H.; Jahandar M.; Moon S.-J.; Song C. E.; Im S. H.Inverted CH3NH3PbI3 Perovskite Hybrid Solar Cells with Improved Flexibility by Introducing a Polymeric Electron Conductor.J. Mater. Chem. C2017, 5, 2883–2891. Google Scholar 44. Bi C.; Chen B.; Wei H.; DeLuca S.; Huang J.Efficient Flexible Solar Cell Based on Composition-Tailored Hybrid Perovskite.Adv. Mater.2017, 29, 1605900. Google Scholar 45. Feng J.; Zhu X.; Yang Z.; Zhang X.; Niu J.; Wang Z.; Zuo S.; Priya S.; Liu S. F.; Yang D.Record Efficiency Stable Flexible Perovskite Solar Cell Using Effective Additive Assistant Strategy.Adv. Mater.2018, 30, 1801418. Google Scholar 46. Li M.; Yang Y. G.; Wang Z. K.; Kang T.; Wang Q.; Turren-Cruz S. H.; Gao X. Y.; Hsu C. S.; Liao L. S.; Abate A.Perovskite Grains Embraced in a Soft Fullerene Network Make Highly Efficient Flexible Solar Cells with Superior Mechanical Stability.Adv. Mater.2019, 31, 1901519. Google Scholar 47. Huang Z.; Hu X.; Liu C.; Meng X.; Huang Z.; Yang J.; Duan X.; Long J.; Zhao Z.; Tan L.; Song Y.; Chen Y.Water-Resistant and Flexible Perovskite Solar Cells via a Glued Interfacial Layer.Adv. Funct. Mater.2019, 29, 1902629. Google Scholar 48. Jia C.; Zhao X.; Lai Y.-H.; Zhao J.; Wang P.-C.; Liou D.-S.; Wang P.; Liu Z.; Zhang W.; Chen W.; Chu Y.-H.; Li J.Highly Flexible, Robust, Stable and High Efficiency Perovskite Solar Cells Enabled by van der Waals Epitaxy on Mica Substrate.Nano Energy2019, 60, 476–484. Google Scholar 49. Zhou Z.; Li X.; Cai M.; Xie F.; Wu Y.; Lan Z.; Yang X.; Qiang Y.; Islam A.; Han L.Stable Inverted Planar Perovskite Solar Cells with Low-Temperature-Processed Hole-Transport Bilayer.Adv. Energy Mater.2017, 7, 1700763. Google Scholar Previous articleNext article FiguresReferencesRelatedDetailsCited ByCheng Y, Wu H, Ma J, Li P, Gu Z, Zang S, Han L, Zhang Y and Song Y (2022) Droplet Manipulation and Crystallization Regulation in Inkjet-Printed Perovskite Film Formation, CCS Chemistry, , (1-21) Issue AssignmentVolume 3Issue 7Page: 2035-2044Supporting Information Copyright & Permissions© 2020 Chinese Chemical SocietyKeywordscross-linkingoperational stabilityelastic grain boundariesmechanical stabilityflexible perovskite solar cellsAcknowledgmentsQ.D. conceived the idea, supervised the project, and conducted the initial experiment. C.G. and Z.Y. fabricated the devices, performed the characterization, and did most of the experiments. X.L., Y.S., and A.W. contributed to the device characterization. Q.D. and C.G. wrote the paper. This work was supported by the National Natural Science Foundation of China (no. 21875089). Downloaded 2,033 times Loading ...